Clik here to view.
Minimum PC requirements
Hi,i want to install cadence 16.6 on my PC but i need to know if my system requirements fair enough or not. so could you please advise about minimum system requirements for orcad 16.6. regards
View ArticleClik here to view.
how to add BB Via in internal layer ??
Hi everyone,how to add buried via in inner layer even though i assigned the pad stack assigned for following producure. (set up--->assign BB via)
View ArticleClik here to view.
errror:while access property in orcad 9.1 ??
Dear all,i did schematic in orcad 9.1 after completed my schematic while access the property for each components i got error.Here i post the error message please reply any one for this question.
View ArticleClik here to view.
Top grid problem facing when trying to put the Routing on single side board?
Hi... I had a simple doubt in the grid placement,that is when i am try to put the single side board the top side routing should not be enabled., for that i had tried to remove the girds on the top...
View ArticleClik here to view.
Orcad capture and Orcad PCB Editor - Connectivity check
Is there a way I can highlight the reference designator or net (ref des) in Orcad capture and it is highlighted on Orcad PCB editor. I am having hard time finding the components from schematic and...
View ArticleClik here to view.
Footrprint Pin movement in not get moved to certain distance in the(.brd)??
Hi..I had placed the components on the board for the single side routing. But when i am trying to move the 2 pin from the component the pin is not get moved. So i had tried the other option that, open...
View ArticleClik here to view.
how to stop the temp file generations in the project folder??
Hi.. When i am trying to update the net list three .dat files are been get executed. but with the three files unnecessarily the temp and log files are been get generated. Similarly when working on the...
View ArticleClik here to view.
Editing the Etch width directly in the board file is possible ?
Hi.. I had tried to put the routing for the board. Before that the color dialog options and constarint manager settings too. But when i am trying to put the track between two points, the track is...
View ArticleClik here to view.
PTH/NPTH Drill to Copper feature spacing issue
Hi , I am facing an issue in Drill to copper feature spacing.Due to my manufacturer requirment I need to have a minmum of 13.78 Mils spacing for any Drill(PTH/NPTH) to any other copper feature.I have...
View ArticleClik here to view.
PTH/NPTH Drill to Copper feature spacing issue
Hi , I am facing an issue in Drill to copper feature spacing.Due to my manufacturer requirment I need to have a minmum of 13.78 Mils spacing for any Drill(PTH/NPTH) to any other copper feature.I have...
View ArticleClik here to view.
Cadance16.6 Shape symbol save error
Hi everybody,I am designing a shape in cadance16.6. There is a rectangular and half of a circle. I merged them and it became like below figure:...
View ArticleClik here to view.
How to edit the DFA bound top & Place Bound top outlines ?
Hi.. I had created the smd footprint with the DFA bound top & Place bound top outlines. Some mistake done in the outline drawing, the dimension want to be extended. So how can i edit the the...
View ArticleClik here to view.
How to edit the dimensions after dimensioning the board?
Hi. I had dimension the board wit the several distance from the origin of board. In case i want o edit the dimension, (i.e)., to decrease or increase the dimension, what the option want to do for that?...
View ArticleClik here to view.
gets stdin not working
HiI am writing a code in Tcl to take user input at run time. For example:puts "Enter input"set a [gets stdin].However, I get the message 1]channel "stdin" wasn't opened for reading in the command...
View ArticleClik here to view.
Footprint Rule of Thumb?
I making footprints for a project and outside of the typical 0603, 0805, etc I'm running into a lot of datasheets that don't have recommended footprints! Our company works in mils and I'm wondering...
View ArticleClik here to view.
BOM_IGNORE IN CAPTURE CIS-163
hi,Is their an option where in i can generate a BOM while ignoring a component in the Schematic using Capture_CIS-163 something like wht it is in HDL
View ArticleClik here to view.
Did the environment paths can be edited in user prefernece option?
Hi.. i had found some tips and tricks for the OrCAD 16.3 editor. In that, they said some commands to work, but how can edit the define variables file in the user preference editor, and how can i save...
View ArticleClik here to view.
How to make a Panel Drawing in cadence Allegro editor?
Hi! can I ask how to make a panel drawing in cadence? I have multiple boards in cadence native file and I need to panel all boards in cadence allegro editor. After that generate a Gerber and ODB++ file
View ArticleClik here to view.
How to remove Component Outline from Bottom Soldermask
Good day to all, Please I need your support and guide on how to solve this Problem.I am using Orcad Pcb Editor 16.0 for my circuit design.After completing the layout,i generated the Gerber files...
View ArticleClik here to view.
After Foot print creation, (.dra) file priniting problem occurs?
Hi..I had created an sample epcos inductor with the specifications provided in data sheet. Then after creation of the footprint, i want to took the print in A4 sheet and then i have to place the...
View Article