Quantcast
Channel: Cadence PCB Design Forum
Viewing all 5525 articles
Browse latest View live

Converting from PADS Logic Designer to OrCad

$
0
0

I have a schematic that was done in Pads Designer 2.5.  I need to convert this to Capture 17.2.

I tried the usual export as an EDIF schematic, then import into OrCad Capture.

This operation always fails.  

Does anyone know how to make this work.  I can't use one of the conversion services, so I need to make this work on my system.

Thanks


unknown usb device (device descriptor request failed)

$
0
0

I am designing a custom Arduino Nano. I followed the Schematic from the official website. Attached is the schematic and the pcb layout for the section of usb-serial bridge. After the pcb was fabricated and assembled, i keep having this error message "unknown usb device (device descriptor request failed) " when i connect usb to my pc. i have tried using different usb cable and pcs but same story. What is the possible cause to this problem and what can i do to make it to work normally? 

Thank you.

Design of DC motor model in pspice

Replaying scripts multiple times

$
0
0

At one time I had a script for rotating (text/parts). It was setup to rotate 90 degrees. Each time I replayed the script it would rotate another 90 degrees. Now when I replay the script it will only rotate 90 degrees once. How do I set up a script to replay each time I run it? Thanks!

Unable to view the pads in 3D while only step model is displayed

$
0
0

Hi,

I am using 17.4v p001 Allegro PCB Designer. I am facing the issue of viewing the 3D of the SOIC component.

When I remove the step model and view only the component with package height I am able to view pads and package height but when I assign a step model to component and view in 3D I only get step model view not the step model and pads view.

I had been using an older version of Allegro too where I didn't face any such issue.

I there any solution to the issue.

MTBF calculations

Text on Manufacturing/Properties layer

$
0
0

We use the above layer to put text from the schematic for connectors, LED's, jumpers. We go to Check-Properties-Graphics and select Valuename and sometimes Valuename2. We change the text block to match what the size of other silk screen ref des are. Then select create, it then tells us how many instances it just created. We turn on the Properties box under Manufacturing and make the color to match our existing silk screen color.

The added text normally comes in tied to pin one of the connectors or cathode of LED's. We then move the text to the outside of the connector outline or just above the LED ref des. The problem is that we have 2 other designers and when they generate this text it create 2 sets of text. One placed on pin one of connectors, cathode of LED's and a second set at the origin 0,0 of the board. We have looked to see if something is checked or not checked on the one computer that only generates the one set. We haven't found any settings different between the 3 computers. All are running the same version of hot fixes, 17.2 S060.

We can work around the problem by deleting the second set at the origin but would like to be able to only create one set on all of the computers.

Drill table Creation in allegro 17.2

$
0
0

Hello,

I am having a problem with creating a drill table in allegro 17.2. To create a drill table and put in the artwork area i have done as below.

Manufacture > Create Drill Table > Pressed Ok(changed nothing in this pop up)

Then I have a drill table shown in the artwork are and I have also put it into the artwork area. but after changing the view from the visibility panel, the drill table disappears.  

Help me with the same.


updating dynamic shapes

$
0
0

hello

is there a command to update dynamic shapes?

i have tried "scriptmode +e" but it does not show any command script for the dynamic shape update.

whenever i need to update dynamic shapes, i would have to open the status window and click the "update to smooth" button.

i would like to update dynamic shapes without opening the status window so that hopefully i could create a funckey to performe the dynamic shape update.

Stamp problems, NET not aligned

$
0
0

I'm having trouble printing schematics made with OrCAD Capture 16.6.

The NETs I place on the electric wires are printed not aligned with the electric wires.

From Capture

From HP Leser Color Printer 

From Printer PDF 

I have tried many printer drivers, but the problem remains.

How do I solve the problem of aligning the NETs?

Thank you

Chip on Board (COB) in Allegro PCB Editor 17.2

$
0
0

Hi,

Any one used on COB technology in Allegro PCB Editor 17.2

I just need to know the challenges faced due to limitation in Allegro PCB Editor 17.2 compared to SiP.

Regards,

Rajesh

Broken net on pth component without connectivity error!!!!

$
0
0

Hello.

I'm working on Orcad 16.6.

Due to a operator error we built a pad PTH (60mil copper with 39mil hole) NOT PLATED.

In Pad Designer this pad passes the check. No errors.

We built the symbol (HEADER 4x1 2.54mm). No errors.

Now we are working on a 4 layer board with this symbol.

We routed some net from inner layers to outer layer on this symbol.

We completed the board. No errors. All lights green on status.

With DFM analysis on ODB++ file we found broken nets on the header (correct because it's unplated)

Why Orcad PCB says all is ok. All green?????

With Mentor and Altium if there's a pth component with unplated pin you can't complete the connectivity

Thank you

Stefano

NPTH hole not visible on 3D Viewer

$
0
0

Hello

I am using 17.x version of Orcad PCB editor . I am unable to view NPTH hole on 3D viewer  , I already enabled display NPTH on preference settings.

For 3D step-file mapping its visibility is much needed

Refer attached short clip

Thanks

Girish community.cadence.com/.../query2.mp4

Replicate Circuits

$
0
0

Can you create a replicate circuit from one .brd design and bring that into another .brd design

Importing XML in Orcad Capture doe not create an OLB.

$
0
0

I am importing XLM files that are obtained from parts vendors using an application called "Library Loader" from

componentsearchengine.com. It creates the XML file which then is imported into Orcad CIS but will not create

a OLB file. Does anyone else have an issue with this. I have attached an example file that will not convert.

community.cadence.com/.../MC14541BDG.xml 


Can't open parameter file....error in artwork creation

$
0
0

Hello,

 I set general parameter (as usual) with metric 2:5 274X

When I create artwork I've this log

Can't open parameter file ... using default values:

     DEVICE-TYPE        GERBER6X00
     G-CODES            NO
     STATIONS-PER-WHEEL 24
     FILM-SIZE          24000 16000
     COORDINATES        ABSOLUTE
     OUTPUT-UNITS       INCHES
     FORMAT             5.3
     ABORT-ON-ERROR     abort film & continue
     SUPPRESS-LEAD-ZEROES     YES
     SUPPRESS-TRAIL-ZEROES    NO
     OPTIMIZE           YES
     SUPPRESS-EQUAL     YES
     SCALE              1.0

Orcad creates a art_param.txt file like this
DEVICE-TYPE           GERBER_RS274X
OUTPUT-UNITS          MM
FILM-SIZE             24000000 16000000
FORMAT                4.6
ABORT-ON-ERROR        NO
SCALE                 1
SUPPRESS-LEAD-ZEROES  YES
SUPPRESS-TRAIL-ZEROES NO
SUPPRESS-EQUAL        YES
UNDEF-APT-CONT        NO

but if I create new artwork Orcad doesn't find it anyway

any ideas?

thanks

Stefano

Agile users

$
0
0

Hi,

I am current looking a software that uploads files and BOM into Agile. We use OrCADs for schematic capture.

We are having a hard time to find the software that would do that. We have perception EDAConnector right now and they have discontinued technical support it since last year.

I am looking forward to hear from you.

Thanks,

Regards,

TiBo

Wire bond guide line support in Allegro PCB Editor 17.2 (COB)

$
0
0

Is there any option in Allegro PCB Editor (COB design) to align the wire bond like we use have in SiP (WB_GUIDE_LINE). Please advise.

OrCAD Capture CIS - CIP database part DRC error

$
0
0

When running a DRC in capture for a schematic, all of my database parts placed from CIP return ORCAP-2434.

For instance from the CIP starter library I placed a molex connector (P/N 26-60-4030)

WARNING(ORCAP-2434): Footprint 'MOLEX_41791-3' specified in PCB Footprint for instance 'P3' is missing. Ensure 'MOLEX_41791-3' is in the library path.

My footprint path is set in my Capture.ini file, so I am unsure how to resolve this issue. I also have not found any information online for ORCAP-2434.

Library .XML to .OLB Import Tool Not Generating the .OLB File

$
0
0

I am using the library loader tool provided by SamacSys to get the .XML files for components I am looking at, but when I import it the .olb file isn't being generated. I am using version 17.2 of OrCAD Capture / PSpice.

Viewing all 5525 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>